1 mbr1060, mbr1080, mbr1090, MBR10100 mbr1060 and MBR10100 are preferred devices switchmode power rectifiers this series of switchmode power rectifiers uses the schottky barrier principle with a platinum barrier metal. these state?of?the?art devices have the following features: features ? guard?ring for stress protection ? low forward voltage ? 175 c operating junction temperature ? epoxy meets ul 94 v?0 @ 0.125 in ? low power loss/high efficiency ? high surge capacity ? low stored charge majority carrier conduction ? pb?free packages are available* mechanical characteristics ? case: epoxy, molded ? weight: 1.9 grams (approximately) ? finish: all external surfaces corrosion resistant and terminal leads are readily solderable ? lead temperature for soldering purposes: 260 c max. for 10 seconds schottky barrier rectifiers 10 amperes, 60 to 100 volts 3 1, 4 to?220ac case 221b plastic 3 4 1 marking diagram ay wwg b10x0 ka device package shipping mbr1060 to?220 50 units/rail mbr1080 to?220 50 units/rail mbr1060g to?220 (pb?free) 50 units/rail MBR10100g to?220 (pb?free) 50 units/rail www.kersemi.com mbr1090 to?220 50 units/rail MBR10100 to?220 50 units/rail mbr1090g to?220 (pb?free) 50 units/rail a = assembly location y = year ww = work week g = pb?free package b10x0 = device code x = 6, 8, 9 or 10 ka = diode polarity mbr1080g to?220 (pb?free) 50 units/rail
mbr1060, mbr1080, mbr1090, MBR10100 www.kersemi.com 2 rating symbol mbr unit 1060 1080 1090 10100 peak repetitive reverse voltage working peak reverse voltage dc blocking voltage v rrm v rwm v r 60 80 90 100 v average rectified forward current (rated v r ) t c = 133 c i f(av) 10 a peak repetitive forward current (rated v r , square wave, 20 khz) t c = 133 c i frm 20 a nonrepetitive peak surge current (surge applied at rated load conditions halfwave, single phase, 60 hz) i fsm 150 a peak repetitive reverse surge current (2.0 s, 1.0 khz) i rrm 0.5 a operating junction temperature (note 1) t j 65 to +175 c storage temperature t stg 65 to +175 c voltage rate of change (rated v r ) dv/dt 10,000 v/ s maximum ratings are those values beyond which device damage can occur. maximum ratings applied to the device are individual str ess limit values (not normal operating conditions) and are not valid simultaneously. if these limits are exceeded, device functional operation i s not implied, damage may occur and reliability may be affected. 1. the heat generated must be less than the thermal conductivity from junction?to?ambient: dp d /dt j < 1/r ja . thermal characteristics maximum thermal resistance, junction?to?case r jc 2.0 c/w maximum thermal resistance, junction?to?ambient r ja 60 c/w electrical characteristics maximum instantaneous forward voltage (note 2) (i f = 10 amps, t c = 125 c) (i f = 10 amps, t c = 25 c) (i f = 20 amps, t c = 125 c) (i f = 20 amps, t c = 25 c) v f 0.7 0.8 0.85 0.95 v maximum instantaneous reverse current (note 2) (rated dc voltage, t c = 125 c) (rated dc voltage, t c = 25 c) i r 6.0 0.10 ma 2. pulse test: pulse width = 300 s, duty cycle 2.0%.
mbr1060, mbr1080, mbr1090, MBR10100 www.kersemi.com 3 figure 1. typical forward voltage figure 2. typical reverse current figure 3. current derating, case figure 4. current derating, ambient figure 5. forward power dissipation 0.6 0 v f , instantaneous voltage (volts) 20 50 10 v r , reverse voltage (volts) 0 110 t c , case temperature ( c) 7.0 3.0 4.0 0 t a , ambient temperature ( c) 20 0 10 8.0 6.0 3.0 0 40 2.0 4.0 0 i f(av) , average current (amps) 10 4.0 3.0 2.0 1.0 0 3.0 i f , instantaneous forward current (amps) i i i f(av) , average forward current (amps) 5.0 3.0 0.2 0.4 0.8 20 40 60 80 0.1 1.0 120 130 140 150 60 80 160 p 5.0 10 6.0 7.0 1.0 0.5 1.0 140 , reverse current (ma) r 10 , average forward current (amps) f(av) 1.0 7.0 8.0 9.0 5.0 6.0 dc square wave dc t j = 25 c 150 c t j = 150 c 125 c 100 c 0.01 25 c 6.0 5.0 8.0 10 9.0 9.0 7.0 5.0 4.0 100 120 140 , average power dissipation (watts) f(av) rated voltage applied square wave dc rated voltage applied r jc = 2 c/w (heatsink) r ja = 16 c/w (no heatsink) r ja = 60 c/w square wave dc t a = 25 c 125 c 100 c 0.5 0.1 0.3 0.7 0.9 100 120 160 1.0 2.0 1.0 2.0 180 200 9.0 8.0 i pk /i av = i pk /i av = 5.0 i pk /i av = 10 i pk /i av = 20
mbr1060, mbr1080, mbr1090, MBR10100 http://onsemi.com 4 to?220 plastic case 221b?04 issue d b r j d g l h q t u a k c s 4 13 dim min max min max millimeters inches a 0.595 0.620 15.11 15.75 b 0.380 0.405 9.65 10.29 c 0.160 0.190 4.06 4.82 d 0.025 0.035 0.64 0.89 f 0.142 0.147 3.61 3.73 g 0.190 0.210 4.83 5.33 h 0.110 0.130 2.79 3.30 j 0.018 0.025 0.46 0.64 k 0.500 0.562 12.70 14.27 l 0.045 0.060 1.14 1.52 q 0.100 0.120 2.54 3.04 r 0.080 0.110 2.04 2.79 s 0.045 0.055 1.14 1.39 t 0.235 0.255 5.97 6.48 u 0.000 0.050 0.000 1.27 f
|
